#-*-makefile-*-################################################
#
#  Mac-on-Linux configuration file (molrc)
#
#  MOL looks for this resource file in the following places
#
# 	$MOLRC			(if started as root)
#	/etc/molrc-hostname
#	/etc/molrc
#
#  All paths are relative /usr/lib/mol
#
###############################################################

#	First, make sure boot_method below is set appropriately. The options are
#	
#	newworld	MOL boots MacOS from a file-ROM (also called "newworld" ROM). 
#			The file-ROM image is simply a copy of the file "Mac OS ROM" 
#			and can be copied from the System Folder (MacOS 8.6 or later). 
#			The ROM file might be missing on older machines if MacOS was 
#			installed with the "minimal installation" option checked (you 
#			can use free application 'tome viewer' to extract the file 
#			from the MacOS installer). 
#
#			Newworld booting currently does not work on 601-based machines (but 
#			the oldworld booting method should work for these machines)
#
#	oldworld	MOL boots MacOS using a boot-rom. Only certain old boot ROMs are
#			supported (in particular, machines similar to the PowerMac 8500
#			are supported). You probably do not want to do an oldworld
#			boot unless you have a very old version of MacOS (<= 8.5).
#
#	macosx		Boot MacOS X (or Darwin). Not yet fully working.
#
#	linux		Boot Linux. Not yet fully working.


boot_method:	newworld


####################################
# Newworld settings
####################################


#	IMPORTANT: Currently it is necessary to strip the first 0x4000 bytes 
#	from the newworld image (the command to use is strip 'nwrom src dest'), 
#	for instance:
#
#		strip_nwrom "/System Folder/Mac OS ROM" /usr/lib/mol/rom/rom.nw
#

newworld_rom:		rom/rom.nw	# path to the stripped ROM-image


####################################
# Oldworld settings 
####################################


#	The following applies to oldworld booting ONLY:
#
# 	You should in general use a ROM-image and an oftree description 
# 	file from the same machine, or from a closely related machine.
# 	If no ofree image is available (or if it doesn't work),
# 	try all the files in the oftrees directory /usr/lib/mol/oftrees.
#
# 	If the lines below are commented, then the ROM/oftree of the
# 	machine running the software will be used (see doc/mol/Status
# 	for more information)
#
#	Sometimes it might be necessary to set 'processor' below to 4.
#	(Do this only if 8 does not work)
#
#	Note: Do NOT use the "strip_nwrom" command on non-newworld images!
#

rom_image:		rom/rom.8500
oftree:			oftrees/oftree.8500


####################################
# Session save/restart (newworld only)
####################################
#
# 	By pressing F12, the MOL session can be saved to
# 	disk. The next time MOL is started, the session will be
# 	restarted (very rapidly). 

session_file:		/tmp/mol_session	# Typically has a size of 30-130 MB


####################################
# Emulation parameters
####################################
#
# 	processor values:  601, 602, 603, 604, G3 (750), G4 (7400)
#
#	In general, you should not set 'processor'. MOL will automatically
#	determine which processor model it should emulate.
#
# NOTE [603 users]
#	Run MOL in 604 mode, or preferably, in G3 mode (G3 mode is default)
#
# NOTE [boot-ROM booting]: 
#	Some boot-ROMs might not run in G3 mode. If so, try 604 mode instead.
#
# NOTE [601 users]
#	Always run in 601 mode (default)
#
# NOTE [G4 users]
# 	If the linux kernel lacks AltiVec support, it is necessary to
# 	explicitly disable the altivec unit below. MOL will probably crash if
#	this is not done. More importantly, 2.2 kernels without altivec support 
#	MIGHT PANIC DUE TO A KERNEL BUG.

processor:		G4
ram_size:		128	# should probably be increased
disable_altivec:	no


####################################
# HFS volumes
####################################
#
# blkdev:	device	flags
#
# 	Device can for instance be /dev/hda, /dev/hda6 or /dev/sda4.
# 	The following flags are supported:
#
# 	-rw/-ro		read-write / read-only [default]
#	-force		export non-HFS partitions (be careful!)
#	-cd		CD

blkdev:         	/dev/hda9       -rw
#blkdev:         	/dev/hdb        -ro
#blkdev:         	/dev/sda        -ro
#blkdev:         	/dev/sdb        -ro
blkdev: 	       	/dev/cdrom      -cd

# WARNING: 
#	Make sure you have backups of any important data before enabling 
# 	read-write permissions. Disk corruption in conjunction with
# 	MOL has been reported (most probably due to a conflict with RamDoubler 9).
#
# Note 1: 
#	You probably want to change the entries above to something
# 	like 'blkdev /dev/hda6 -rw'. Use pdisk/disklabel to find out
# 	what partition numbers your HFS volumes have. If you do not
# 	change this, then the volume might end up locked (even if
# 	it is not mounted by linux).
#
# Note 2: 
#	If there is an error 'file system map inconsistent' during boot,
# 	then write privileges should be enabled (this appears to be a MacOS bug
# 	which sometimes prevents booting from a locked volume).
#
# Note 3: 
#	Which volume MacOS tries to boot from is dependent
# 	upon the order of the blkdev lines above.
#


####################################
# Mouse
####################################
#
# 	One of the following mouse settings should probably be used:
#
#	 device		protocol
#	-------------------------
#	 /dev/usbmouse,	  usb		# might work with ADB too
#	 /dev/input/mice, usb		# might work with ADB too
#	 /dev/adbmouse,	  adb
#	 /dev/mouse,	  ps2
#	     -		console		# for old kernels

mouse_device:		/dev/input/mice
mouse_protocol:		ps2		# usb (ps2), adb, console
mouse_dpi:		140		# higher == slower mouse
use_x_cursor:		yes		# use X cursor as mouse cursor


####################################
# Ethernet
####################################
#
# netdev:	device [-sheep | -tap | -tun]
#
#	Note: It is possible to configure up to three network 
# 	interfaces simultaneously. 
#

#netdev:		tap0
netdev:			eth0
netdev:			eth1


#######################################
# Video configuration
#######################################

# Startup resolution and depth (used as a *HINT* only)
resolution:		640/480/75		# width/height[/Hz]
depth:			16			# 

# X-display to be used ($DISPLAY is used if commented)
#xdisplay:		remote.host.address:0.0

# The tool 'molvconfig' configures the fullscreen modes.

start_on_console:	yes	# switch to console initially
autoswitch_console:	yes	# allow automatic switching to console
enable_console_video:	yes	# Full-screen video is *much* faster than X-video
enable_xvideo:		yes	# 
use_backing_store:	no	# Set to 'yes' only if the X-server is remote.
vt:			12	# VT-number to use for full-screen video

# For VNC information, visit http://www.uk.research.att.com/vnc/

enable_vncvideo:	no	# Enable the VNC server
vnc_port:  		5900	# port to use for VNC


####################################
# Keyboard
####################################
#
# Almost all Apple keyboards have an unique ID, and it affects how MacOS
# deals with key map tables and such.  Ideally, we'd want to get this info
# from /dev/adb, but for now please specify.
#
# Hint: *Usually* the ID is printed during Linux/PPC's bootup.
#	.....
#	adb devices: [2]: 2 22 [3]: 3 1
#	              ^     ^
#	              |     +- The second number ("22" here) is the keyboard ID.
#	        This "2" indicates that it's an ADB keyboard.
#
# Sample IDs:
# ID #
# ----
#   1  Apple Standard Keyboard
#   2  Apple Extended Keyboard
#  22  JIS Apple Keyboard II
# 195  PowerBook Titanium
# 200  JIS USB Keyboard
#

keyboard_id: 195

# Older kernels in general use ADB keycodes. MOL tries to auto-detect
# whether ADB or linux keycodes are used, but this setting can be forced
# by uncommenting the following line:

#use_linux_keycodes:	yes

# It is possible to tune the keymapping by adding
# 'remap_key keycode adb_keycode' lines.

#remap_key:	31 2		# Maps keycode 31 to ADB keycode 2
#remap_key:	41 50 		# Perhaps useful on PB Titanium

# Files containg key-mappings can also be read. The format
# of the file is 'keycode: adbcode'

#kbd_file:	filename


####################################
# Console video gamma
####################################
#
# Gamma correction for the display. "gamma" takes one floating number
# between 0.1 and 10.0 or three floating numbers specifying each R, G, and B
# value separately.  A larger value gives a brighter display.  No correction
# is made when the value is 1.0.
# Please note that the xvideo mode is not affected by this setting.

gamma:			1.0			# one value for all RGB
#gamma:			1.0 1.0 1.0		# R G B separately


####################################
# Sound
####################################

play_startboing:	no		# Play startboing
disable_osi_sound:	yes		# Disable sound?


####################################
# Misc
####################################

logfile:		/tmp/mol-logfile	# only used in debugger mode